Firearms / Revolvers / Ruger Redhawk

A special extra shot is available on site and can be purchased


Ruger Redhawk


.44 Magnum


5 shots

In package


Where we could see it






The Ruger Redhawk is a DA/SA, large-frame revolver that was first introduced in 1979 by Sturm, Ruger & Company. Made from high-grade steel, it is available in a stainless steel finish. The Redhawk is reinforced to handle extra stress, making it very popular for use by handloaders as it is able to handle both.45 Colt and .44 Magnum loads. In addition, the cylinder itself is longer than most competitors', allowing ammunition to be loaded to a longer overall length. This allows for either increased powder capacity, heavier (and therefore longer) bullets without compromising the powder load, or a combination of both. Custom ammunition manufacturers even have loads made specifically for Ruger revolvers that cannot fit in shorter chambers or revolvers of weaker construction (such as the Smith & Wesson Model 29). This makes the Redhawk popular as a bear defense gun among hunters and trappers.

The Redhawk was the first large-bore double-action revolver made by Ruger. It was designed by Harry Sefried, who previously worked for High Standard Manufacturing Company, where he designed the High Standard Sentinel revolver. The grip profile of the Sentinel was used on the "Six" line of Ruger .357 double-action revolvers, which included the Ruger Security-Six and its variants, the Service-Six and Speed-Six. These revolvers were produced from 1970 to 1988, and were unlike other double-action revolvers in that they used a one-piece frame, rather than a removable sideplate, which lent them superior strength. The Redhawk, introduced in 1980, was a scaled-up and improved version of the Security-Six, the target model, with a square butt grip, adjustable sights, and 5.5- and 7.5-inch barrel lengths. The Redhawk was available in blued or stainless steel, and was primarily used by handgun hunters. The Redhawk, designed for long-term use with the heaviest .44 Magnum loads, included a new latch at the crane, to firmly lock the cylinder at front and rear, a feature last seen in the Smith & Wesson's triple lock design, discontinued in 1915.

The Ruger Redhawk uses modern coil springs design instead of old-fashioned leaf springs that are found in most modern revolvers. The revolvers also used a single spring for both the hammer and the trigger, and this meant that the force required to pull the trigger was higher than similar offerings from other manufacturers, and there was no way to adjust or correct this as it was inherent in the single-spring design.

The revolver has forward ramp sights with four different interchangeable sight inserts. The rear sights are fully adjustable, featuring a white outline. The Redhawk is available with scope mounts and rings.

The Redhawk holds six rounds of ammunition in its cylinder and until recently was available with a 4-inch, 5.5-inch, or 7.5-inch barrel. A 4.2-inch barrel was also recently added to accommodate the Canadian rules for minimum barrel length (the same was later done for the GP100 revolver). When introduced it was only offered in .44 Magnum/.44 Special. Later on .41 Magnum, .357 Magnum/.38 Special, .45 Colt and .45 ACP/.45 Colt were added to the lineup. Gradually options in chambering were pared down, and by 2007 the Redhawk was again only offered in .44 Magnum. However, in 2008 Sturm, Ruger & Co. once again began marketing the Redhawk in .45 Colt chambering.

In June 2015 Ruger announced a production Redhawk version that supports both the rimmed .45 Colt round and the rimless .45 ACP round. Ruger achieves this multi-cartridge functionality by partially machining the cylinder for use of moon clips for the .45 ACP while still retaining enough ledge on the cylinder to allow proper .45 Colt headspacing. For several years gunsmiths have been customizing DA/SA revolver cylinders (manufactured using modern metallurgy) of .45 Colt, .454 Casull or .460 S&W Magnum chamberings to accept .45 ACP (and possibly other rounds) with moon clips in addition to the revolver's original round(s). However, Ruger's .45 ACP/.45 Colt Redhawk offering is one of the first factory-produced, manufacturer-standard revolver models with such a machined cylinder.

Any questions?

Use our chat, we are happy to answer you within our opening hours.

ADDRESS: 1065 BUDAPEST, NAGYMEZŐ UTCA 37-39 | PHONE: +36 30 712 32 59
FAQ | Terms and Conditions | GDPR

Copyright 2019 © Budapest Shooting